A

Andrews Cooper Technology

Custom automation, testing for medical devices

Acoustic and Audio Test Engineer

Hardware Validation & TestingConfirmed live in the last 24 hours
Full-timeRedmond, WA, USA$104k - $175k

About the Job

Requirements

  • A Bachelor of Science in Electrical Engineering from an accredited university, or equivalent experience in a related field.
  • Two to six years of hands-on professional experience in test and verification for consumer electronics; this is a target range, not a hard requirement.
  • Strong understanding of system-level verification and validation, as well as component- and board-level verification.
  • Experience with acoustic verification, including anechoic chambers, head and torso simulators, microphone and speaker measurement, and hands-on execution of acoustic validation tests.
  • Ability to develop acoustic tests by translating requirements into validation tests, establishing sound measurement methods, and documenting procedures for repeatable execution by others.
  • Experience with audio and acoustic analysis platforms, including Audio Precision, Listen Inc. SoundCheck, and HEAD acoustics ACQUA / LabCore.
  • Experience with board-level audio electronics verification involving speakers, microphones, codecs, and amplifiers.
  • Understanding of measurement rigor, including calibration, noise floor, fixture and positioning effects, repeatability, and measurement uncertainty.
  • Ability to create, modify, interpret, review, and execute test plans, and guide others through them.
  • Knowledge of low-speed interfaces used in wearable consumer devices, including I2C, I3C, SPI, UART, GPIO, and audio interfaces such as I2S and TDM, including register-level configuration from device datasheets.
  • Experience using bench instrumentation, including an oscilloscope, multimeter, power supply, and logic analyzer.
  • Root cause analysis and failure diagnostics, including isolating whether a failure originates in the electrical path, transducer, or fixture.
  • Ability to write test procedures and reports and coordinate day to day with teams across multiple sites and time zones.
  • Must work on-site in Redmond, Washington; fully remote work is not available.
  • Must be legally authorized to work in the United States without sponsorship.
  • Must pass a background check.
  • Must be able to travel for work-related purposes as needed and have access to reliable transportation due to the nature of the business and multiple client sites.

Responsibilities

  • Work in a laboratory environment on new consumer electronics products in a fast-paced setting with evolving requirements.
  • Spend approximately 60% of the role developing acoustic tests and executing validation tests, 20% on audio electronics verification, and 20% on technical program management.
  • Review existing test plans for technical accuracy and correctly interpret their intent; where acoustic coverage is not available, build the test and fixture, and revise existing methods as requirements change.
  • Coordinate electrical and audio electronics verification performed by partner teams at other sites with the verification lead, track issues raised against partner teams, and report status through written follow-up and task tracking across time zones.
  • Run audio electronics verification directly when needed.

Desired Qualifications

  • Coordinate across audio development and verification teams, including logistics, timelines, and issue resolution.
  • Willingness to learn across electrical, audio electrical, and acoustic verification disciplines and work largely autonomously with minimal supervision after onboarding.
  • As ramp-up progresses, document key processes, tools, and lessons learned so they can be revisited and used to build on coaching conversations.
  • Demonstrated appetite for learning new measurement domains.
  • New product introduction experience across EVT, DVT, and PVT builds.

About the Company

Andrews Cooper Technology

Custom automation, testing for medical devices

Andrews Cooper Technology provides product development and automation engineering services for medical devices and consumer products, delivering custom automated manufacturing and test solutions and managed engineering services on-site or at its facilities. Its process starts with understanding client needs, then designing, building, and validating automated equipment and test rigs that integrate with production lines, followed by commissioning and ongoing support. The company differentiates itself by offering end-to-end, custom solutions with lifecycle coverage from design to deployment to maintenance, working with startups through large corporations. Its goal is to help clients bring safe, reliable, and efficient products to market through practical engineering, scalable automation, and ongoing support.

Company size
51-200
Company stage
Seed
Total funding
$30K
Headquarters
McMinnville, Oregon
Founded
2000

Recently Posted Jobs

Explore more opportunities at Andrews Cooper Technology

See more jobs