B

Broadata Communications

Manufactures fiber, HDBaseT, IP transmission solutions

Senior Hardware Design Engineer

Board & Electronics DesignConfirmed live in the last 24 hours
Full-timeTorrance, CA, USA$130k - $180k

About the Job

Requirements

  • A B.S. in Electrical Engineering or a related field is required.
  • At least 8 years of hands-on hardware design experience with high-speed analog/digital, embedded, video, networking, or mission-critical electronic products is required.
  • Strong hands-on experience with Altium Designer for schematic capture and PCB layout is required, including multi-sheet schematics, design rules, libraries, variants, bills of materials, output jobs, and manufacturing release packages.
  • Demonstrated experience designing complex multilayer printed circuit boards with controlled impedance, differential pairs, high-speed connectors, high-density components, power distribution, grounding, shielding, electromagnetic interference/electrostatic discharge protection, and manufacturability constraints.
  • Practical experience with high-speed simulation, stack-up planning, signal integrity, power integrity, and root-cause analysis for multi-gigabit-per-second interfaces.
  • Working knowledge of digital video and data interfaces, especially HDMI, DisplayPort, USB-C/USB 3.x, SMPTE SDI, DVI, Ethernet, 10G Ethernet, SFP/SFP+, and related standards.
  • Experience interfacing with microcontrollers, application processors, FPGAs/CPLDs, video scalers, video receivers/transmitters, Ethernet PHYs/switches, high-speed memory, and communication interfaces including I2C, SPI, UART, RS-232, RS-485, USB, SDIO, Ethernet, and PCIe.
  • Strong hardware debugging skills to isolate failures to schematic, layout, component, firmware interaction, signal integrity, power integrity, electromagnetic interference/electrostatic discharge, or manufacturing causes.
  • Ability to read, understand, create, edit, and review multimedia printed circuit board schematics and high-speed layouts.
  • Strong understanding of FPGA/SoC/processors, memory systems, video interfaces, power subsystems including linear and switching topologies, electrostatic discharge/electromagnetic interference protection, and serial interfaces.
  • Ability to identify root causes of complex system problems, including internally reported failures and customer returns, using structured methods such as Ishikawa/fishbone analysis.
  • Ability to provide completion-time estimates for design, simulation, bring-up, and validation requirements.
  • Ability to perform soldering, rework, assembly, board modification, and laboratory testing.
  • Ability to work with little supervision, prioritize multiple tasks, meet deadlines, and work extended hours as needed.
  • Ability to occasionally move throughout facilities and climb stairs; occasionally bend and reach; use standard computer and phone equipment; sit or stand for one to twelve hours per day; and lift and carry up to 50 pounds unassisted.

Responsibilities

  • Own board-level hardware design from requirements review, architecture definition, and component selection through schematic capture, PCB layout support, prototype bring-up, DFM/DFT review, verification, and production release.
  • Create and maintain complex multi-sheet schematics in Altium Designer for video, high-speed digital, embedded processor, FPGA/CPLD, power, analog, isolation, protection, and fiber-optic interface circuits.
  • Own or directly support PCB layout in Altium Designer, including component placement, stack-up definition, controlled impedance, design rules, routing constraints, length matching, differential-pair tuning, return-path control, via strategy, and manufacturability review.
  • Define and review high-speed layout requirements for HDMI, DisplayPort, USB-C/USB 3.x, DVI, 3G/12G SDI, SFP/SFP+, 1G/10G Ethernet, PCIe, DDR2/DDR3/DDR4, LVDS, MIPI, and similar interfaces.
  • Perform pre-layout and post-layout high-speed circuit simulation and signal-integrity/power-integrity analysis to reduce jitter, crosstalk, insertion loss, return loss, reflections, via stubs, impedance discontinuities, electromagnetic interference risk, and power noise.
  • Use Ansys HFSS or similar 3D electromagnetic tools, when applicable, to analyze connectors, high-speed launches, vias, back-drill structures, transitions, stubs, and other critical discontinuities.
  • Use simulation and layout review to guide connector selection, cable interface design, electrostatic discharge/electromagnetic interference protection, common-mode choke usage, reference-plane continuity, grounding, shielding, and high-speed routing strategy.
  • Design and review power architecture, switching and linear power supplies, sequencing, protection circuits, thermal considerations, and power-distribution networks for embedded products.
  • Lead board bring-up, debugging, and root-cause failure analysis for prototypes, pilot builds, sustaining engineering changes, end-of-life redesigns, and customer return issues.
  • Use oscilloscopes, TDR/VNA, protocol analyzers, bit-error-rate/eye-diagram tools, logic analyzers, thermal tools, and standard laboratory equipment to validate high-speed, power, and embedded hardware performance.
  • Support verification and validation testing, including HDMI/DisplayPort/SDI/Ethernet interface checks, EMC/ESD testing, environmental stress screening, reliability testing, and compliance-related testing for medical or mission-critical products.
  • Prepare and review engineering change order/engineering change notice packages, bills of materials, manufacturing release packages, layout notes, simulation summaries, design review materials, test notes, and corrective-action documentation.
  • Work with product management, mechanical, firmware, FPGA, software, test, manufacturing, vendors, and original design manufacturing partners to deliver manufacturable and reliable products.
  • Lead and participate in schematic, layout, signal-integrity/power-integrity, design-for-manufacturing, and design-verification reviews, and mentor junior engineers and PCB designers on high-speed layout and troubleshooting practices.

Desired Qualifications

  • A Master of Science in Electrical Engineering is a plus.
  • Experience with analog and digital video products, video transmission over copper and fiber, AV-over-IP, SDVoE, video processing, capture, display, and interface conversion is preferred.
  • Hands-on Ansys HFSS experience for 3D electromagnetic extraction and analysis of high-speed channels, connectors, vias, launches, back-drill structures, stubs, and board transitions is preferred.
  • Experience with other signal-integrity/power-integrity tools such as Ansys SIwave, Keysight ADS, HyperLynx, Sigrity, or similar tools is a plus.
  • Experience developing hardware for medical, military, industrial, or other high-reliability products and supporting standards such as IEC 60601, IEC 60601-1-2, ISO 13485, MIL-STD, or equivalent is a plus.

About the Company

Broadata Communications

Manufactures fiber, HDBaseT, IP transmission solutions

Broadata Communications designs and builds equipment that transmits video, audio, data, and control signals over fiber, HD-BaseT, and increasingly IP networks. Its products are market-driven, aimed at delivering reliable, ready-to-use connectivity solutions for professional A/V, broadcast, medical, education, government, transportation, and other sectors. The company’s devices work by sending multiple signal types across fiber cables or HDBaseT links, and are expanding to IP-based distribution to fit modern networked environments. What sets Broadata apart is its focus on quickly bringing dependable, field-ready solutions to a wide range of high‑profile customers and industries, backed by a privately held, California-based organization with a track record across entertainment, broadcast, medical, and more. The goal is to stay at the forefront of the technology and provide dependable connectivity options that meet evolving customer needs in a timely manner.

Company size
11-50
Company stage
Not listed
Total funding
Not listed
Headquarters
Torrance, CA
Founded
2000

Recently Posted Jobs

Explore more opportunities at Broadata Communications

See more jobs