Embedded Hardware Engineer - Electro Optical Systems

Product Scope:

• The hardware you design goes into a defense- and public-safety-focused product line. Direct experience with these systems is a plus, not a prerequisite — but you should be interested in working on:
• Gyro-stabilized multi-axis gimbals (2-axis and 4-axis) with EO/IR sensor payloads
• High-intensity searchlights (HISL) and associated high-power drive electronics
• Counter-UAS and detection systems
• Airborne, land, and maritime platform integrations, including qualification to environmental, shock/vibration, and EMI/EMC requirements

Responsibilities:

• Hardware Design & Development
• Own board-level design from requirements through release: architecture, component selection, schematic capture, and PCB layout for mixed-signal, high-speed digital, and power boards.
• Design and implement circuitry for real-time video paths, brushless motor control and stabilization, serial communications, and DC/DC power regulation and distribution.
• Apply disciplined power, ground, and high-speed design practice: stackup and impedance control, controlled return paths, plane partitioning, decoupling strategy, length/skew matching, and signal integrity for multi-gigabit and clocked interfaces.
• Design for EMI/EMC, thermal performance, and environmental robustness in size-, weight-, and power-constrained enclosures.
• Integrate and configure STM32 (and similar ARM Cortex-M) microcontrollers and FPGAs, working closely with firmware engineers on pinout, boot, clocking, memory, and interface definition.
• Produce and maintain complete design documentation: schematics, BOMs, fabrication and assembly drawings, interface control documents, and test procedures.


• Bring-Up, Debug & Validation
• Perform first-article board bring-up and power-on characterization, isolating and resolving hardware faults down to the component and signal level.
• Use the full bench toolkit daily: oscilloscopes (including high-bandwidth and mixed-signal), spectrum analyzers, logic and protocol analyzers, function generators, DMMs, power supplies and electronic loads, thermal imaging, and network/serial test tools.
• Debug and validate hardware interfaces including SPI, I²C, UART/RS-232/RS-422/RS-485, Ethernet, HDMI, SDI, CAN, USB, and LVDS/differential video links.
• Measure and verify power rails, sequencing, ripple, transient response, efficiency, inrush, and load regulation; characterize noise coupling and grounding issues in real hardware rather than on paper.
• Plan and execute design verification testing; support EMI/EMC and environmental qualification campaigns and drive corrective design changes based on results.


• Production & Field Support
• Act as the hardware technical resource for manufacturing and service personnel — resolving build, test, and yield issues and supporting escalations that exceed technician-level diagnosis.
• Develop test fixtures, ATE requirements, functional test procedures, and troubleshooting guides that let production and service teams diagnose faults independently.
• Perform failure analysis on returned and fielded units; determine root cause, recommend corrective action, and close the loop through engineering change orders and design improvements.
• Apply design-for-manufacturability, design-for-test, and design-for-serviceability principles from the start of each project.
• Provide occasional remote or on-site support for fielded systems.

Basic Qualifications:

• Bachelor's degree in Electrical Engineering, Computer Engineering, or a related discipline.
• 5+ years of hands-on embedded hardware design experience, including schematic capture and PCB layout of production hardware.
• Demonstrated proficiency with lab instrumentation — you can independently select the right instrument, set up the measurement correctly, and interpret what you see.
• Practical design and debug experience with embedded digital interfaces (SPI, I²C, UART/RS-232/RS-422, Ethernet) and at least one high-speed video or serial interface (HDMI, SDI, LVDS, or similar).
• Working experience designing around microcontrollers (STM32 or comparable ARM Cortex-M) and FPGAs.
• Solid grounding in power electronics: DC/DC topologies, regulation, sequencing, protection, and power/ground plane design.
• Ability to read and interpret datasheets, reference designs, and errata, and to make defensible component and topology trade-offs.
• Strong analytical and written communication skills; able to document findings clearly for engineering, production, and customer audiences.
• Must be a U.S. Person as defined under ITAR/EAR and eligible to work on export-controlled programs.
• Up to 10% travel required.

Additional Qualifications:

• Experience with Altium Designerand associated library and release management practices.
• Brushless (BLDC/PMSM) motor drive and closed-loop control hardware experience; familiarity with stabilization systems, gyros, encoders, or IMUs a plus
• Real-time video and imaging electronics experience (EO/IR sensors, camera interfaces, video encoders/serializers).
• FPGA design exposure (VHDL/Verilog) or close collaboration with FPGA teams on interface definition and timing closure.
• Firmware/embedded C experience sufficient to write bring-up and diagnostic code.
• Familiarity with aerospace or defense qualification standards (e.g., DO-160, MIL-STD-810, MIL-STD-461) and IPC workmanship standards.
• Experience supporting fielded airborne, land, or maritime systems, or prior work with EO/IR gimbals, high-intensity searchlights, or Counter-UAS products.
• Background in structured root-cause analysis and continuous improvement methodologies.