U

USEMCO

Designs and builds metal water equipment

WEM Tester

Inspection & TestConfirmed live in the last 24 hours
Full-timeTomah, WI, USAIn-person

About the Job

Requirements

  • A high school diploma or general education degree (GED) is required.
  • One to three months of experience in simple assembly is required.
  • Experience in a metals manufacturing environment is a plus.
  • Problem-solving skills to address issues involving a few concrete variables in standardized situations are required.
  • Ability to use basic high school mathematics is required.
  • Ability to read and interpret a tape measure is required.
  • Ability to read a machining scale is a plus.
  • Prioritization, organizational, and attention-to-detail skills are important for the role.
  • Ability to read and comprehend simple instructions, short correspondence, and memos is required.
  • Ability to write simple correspondence and complete daily labor or testing reports is required.
  • Ability to stand and walk on the production floor for more than eight hours per day is required.
  • Ability to walk up steps and stand on top of a low platform is required.
  • Ability to use hands and fingers to grasp parts, change tooling, push and pull tools, and read and record pressure-gauge results is required.
  • Ability to write information in a logical flow is required.
  • Ability to read and respond throughout the day on an ongoing basis is required.
  • Ability to communicate with others in person is required.
  • Ability to walk, bend, reach, climb, stoop, kneel, or crouch frequently is required.
  • Ability to lift and carry 30 to 60 pounds occasionally is required.
  • The role requires frequent twisting, forward bending, reaching to the side, head and neck rotation and flexion/extension, fine manipulation of both hands, forearm twisting, and light, medium, and firm grip force; it requires constant walking, standing, and forward reaching, and occasional squatting/crouching, stair climbing, head/neck static posture, and high-repetition hand movements.
  • Driving is rarely required. The role does not require sitting, crawling, reaching above the shoulders, kneeling, or ladder climbing.

Responsibilities

  • Assemble parts for loading on the testing bench.
  • Visually examine parts for defects such as cracks and pinholes.
  • Measure pressure-test results and log the data.
  • Separate and mark defective parts according to job specifications and department procedures.
  • File or deburr surplus metal from parts as needed.
  • Stamp parts accurately after successful completion of the test.
  • Disassemble parts after testing is complete.
  • Tag and move parts to the staging area for storage.
  • Prepare the proper work-order and routing documentation.
  • Safely pressure-test and/or leak-test grey iron, ductile iron, steel, and stainless-steel castings while following all work instructions.
  • Test boilers, tanks, fittings, pipes, and similar objects to detect and locate leaks using compressed air or water pressure.
  • Install fittings to seal outlets and connect objects to high-pressure air or water lines using hand tools.
  • Activate an air compressor or water pump until the gauge registers the specified internal pressure.
  • Observe the gauge for pressure loss and examine objects for escaping air or water to detect leaks.
  • Mark objects at leak sources for subsequent repair.
  • Apply soap solution to an object’s surface or immerse the object to help locate air leaks when needed.
  • Test objects under high pressure when needed to ensure compliance with product safety ratings.
  • Maintain a high level of quality and report test results accurately.

About the Company

USEMCO

Designs and builds metal water equipment

USEMCO produces equipment for clean water and wastewater handling. Its in-house Engineering Department designs and builds projects to customer specifications, and it can engineer and fabricate any metal structure. The company is ASME certified to manufacture pressure vessels.

Company size
11-50
Company stage
Not listed
Total funding
Not listed
Headquarters
Tomah, WI
Founded
1963

Recently Posted Jobs

Explore more opportunities at USEMCO

See more jobs