T

Tesla

Makes electric cars, robotaxis and grid batteries

Supplier Industrialization Engineer - Ferrite and Magnetic Components

Process EngineeringConfirmed live in the last 24 hours
Full-timeGrünheide (Mark), GermanyNo salary listedIn-person

About the Job

Requirements

  • A degree in Electrical, Materials, Physics, Magnetic Materials, Manufacturing, or related Engineering, or equivalent experience.
  • At least 3 years of experience industrializing, manufacturing, or qualifying ferrites, permanent magnets, powder cores, or wound magnetic components such as transformers, inductors, chokes, or wireless-charging coils.
  • Hands-on fluency with ferrite or magnet manufacturing processes (pressing, sintering or annealing, grinding, gapping, and magnetizing) and/or winding processes (bobbin, toroid, foil, litz, impregnation, and termination).
  • Working knowledge of magnetic materials and circuit behavior, including B-H loops, permeability versus bias and temperature, core loss, skin and proximity effects, leakage, saturation, magnetostriction, and insulation systems.
  • Ability to specify and interpret magnetic tests, including LCR, B-H analyzer, core-loss measurement, impedance or network analysis, hipot or partial discharge, and thermal derating.
  • Proven ownership of APQP or PPAP (or equivalent), PFMEA, control plans, MSA, SPC, and Cpk on magnetic and dimensional characteristics.
  • Experience with incoming material control for powders, oxides, rare-earth magnets, magnet wire, and insulation, including lot traceability and aging or humidity sensitivity of ferrites and magnets.
  • Structured problem-solving experience using 8D, FTA, and DOE, and comfort working with data.
  • Candidates are expected to uphold and actively promote sustainability principles in daily work, operating in line with Tesla Global EHS&S Policy and EMAS requirements.

Responsibilities

  • Own industrialization of ferrite and magnetic components from powder and melt through winding, assembly, testing, and stable mass production, including MnZn and NiZn ferrites, powder and nanocrystalline cores, sintered and bonded magnets, transformers, inductors, common-mode chokes, wireless-charging coils, and current-sense magnetics.
  • Develop and qualify supplier processes across the magnetic value chain: powder preparation, pressing or injection, sintering or annealing, grinding and gapping, coating, magnetization, winding with magnet wire or foil, impregnation or varnish, termination, and final electrical testing.
  • Lead design for manufacturability with Tesla Power Electronics, Motor, and Charging design teams, closing core geometry, gap, winding window, leakage, parasitics, thermal, and insulation issues before tooling and ferrite-tool steel are cut.
  • Define material and process special characteristics, including AL or inductance, permeability, core loss (Pcv) versus B and f, saturation (Bs), Br/Hc for magnets, DCR, leakage inductance, turns ratio, hipot or partial discharge, and thermal aging.
  • Qualify lines and materials, including furnace profiles, atmosphere control, density and shrinkage, grinding capability, gap consistency, winding tension and layering, varnish fill, magnetization fixtures, and 100% or sample electrical testing (LCR, B-H, core loss, and hipot).
  • Drive APQP and PPAP (or Tesla equivalent), including material certifications, incoming powder or magnet lot control, and process capability on magnetic and dimensional characteristics.
  • Audit ferrite, magnet, and wound-component factories against IATF 16949, VDA 6.3, and Tesla requirements, and extend control into sub-tier powder, oxide, rare-earth, copper, and insulation suppliers.
  • Lead on-site debugging of magnetic drift, high core loss, saturation, noise or magnetostriction, insulation failures, and winding defects using first-principles magnetics and process data.
  • Translate Tesla application conditions (high frequency, high ripple, DC bias, thermal cycling, vibration, and humidity) into material selection, process windows, and qualification against AEC-Q200, IEC 60404, IEC 61558 or 62368, and applicable automotive environmental requirements.
  • Partner with Purchasing and Design on cost, dual-source, and localization of ferrites, magnets, and wound magnetics without sacrificing B-H performance or reliability.
  • Build capacity and yield models that match Tesla ramp, and challenge sintering OEE, grind yield, copper fill, and scrap.

Desired Qualifications

  • Experience with power electronics, EV drivetrain, or high-frequency magnetics is preferred.
  • Experience with EV onboard charger, DC-DC, drive inverter, motor, or wireless-charging magnetics is preferred.
  • IATF or VDA audit experience is preferred.
  • Six Sigma or CQE is preferred.
  • JMP, Minitab, or Python is a plus.
  • FEA magnetics using Maxwell or FEMM is a plus.

About the Company

Tesla

Makes electric cars, robotaxis and grid batteries

Tesla makes electric cars and batteries that store power for homes and utilities, and it develops self-driving software and humanoid robots. In 2023, its Model Y became the first electric vehicle to rank as the world's best-selling car. Buyers order the Model 3 sedan, Model Y SUV, or Cybertruck pickup directly from Tesla instead of through dealers, and they charge on its Supercharger fast-charging network. It also sells Megapack and Powerwall batteries, runs a robotaxi service, and charges drivers a monthly fee for self-driving software that still needs their supervision. Tesla was founded in 2003, with Elon Musk as its lead early investor and a recognized co-founder, and it is based in Austin, Texas.

Company size
10,001+
Company stage
IPO
Headquarters
Austin, TX
Founded
2003

Recently Posted Jobs

Explore more opportunities at Tesla

See more jobs